Balanced
Listado balanced
-
75" diaphragm compression driver frequency response (-6 db) 60 hz - 18 khz frequency range (-10 db) 56 hz - 20 khz nominal coverage (-6 db) 90° conical dmt maximum spl db peak amplifiers power output w continuous class d (500 w lf, 500 w hf) w peak input impedance xlr / ¼": 40 ko balanced / 20 ko unbalanced xlr / ¼" mic mode: o balanced rca: 10 ko controls power, gain a, gain b, mic/line, lf mode (ext sub/norm/deep™), hf mode (flat/vocal boost), front led (on/off/limit) indicators power, signal a, signal b, standby, limit, mic connectors balanced female xlr/¼" line/mic level input, balanced female xlr/¼" line level input, dual balanced male xlr full range line level out, balanced male xlr "mix" out, stereo rca line level input, remote gain control, locking iec power connector cooling on demand, 50 mm variable speed fan amplifier protection thermal limiting, output overcurrent, overtemperature muting, guardrail™ transducer protection thermal limiting, excursion limiting ac power input universal power supply vac, 50 to 60 hz ac power consumption (1/8 of full power) 100 vac, 2indicador led de encendido, en la parte delantera 45 kg available accessories k10 tote, k10 yoke, m10 kit -k10 1puntos de conexión del yugo m5 8casquillo para poste tilt-direct™ de ángulo doble 913 a enclosure material impact resistant abs finish black paint grille rugged powder-coated steel dimensions (hwd) inches dimensions (hwd) mm 519 x 320 x 300 weight (net) 32 lb / 14patas antirresbalamientospecifications k10 configuration multipurpose 2-way transducers low-frequency high-frequency 10" cone transducer 1asas de aluminio fundido 5módulo de alimentación eléctrica 6parrilla de acero 3puntos de instalación m10 7
-
6 kohms, balanced line input: 20 kohms, balanced stereo aux returns: 20 kohms, balanced cd/tape in: 24 kohms, balanced output impedance main: 240 ohms, balanced; 120 ohms, unbalanced ctrl room, aux sends: 120 ohms tape output: 1 kohm phones output: 25 ohms vu meters main left and right: 4 segments: clip (+ led = 0 dbu ac power requirements external power supply output: 185 vac x ma (3-pin ac power connection) external power supply ac input: u50 compact mixer frequency response mic input to any output (trim at 0 db): +0, -1 db, 10 hz to 150 khz, -3 db, 10 hz to 200 khz distortion thd and smpte imd; 20 hz to 20 khz mic input to main output: noise 20 hz to 20 khz bw (120-ohm source impedance) equivalent input noise (ein): -129 dbu residual output noise: channel and main mix levels off main, ctrl room, phones: -106 dbu common mode rejection ratio (cmrr) mic in: 60 db @ 1 khz gain @ maximum crosstalk adjacent inputs or input to output: -90 db @ 1 khz input gain control range: 0 db to +50 db equalization mono channel eq: high: ±15 db @ 12 khz; low: ±15 db @ 80 hz mixer rated output main, aux, control room: +4 dbu maximum rated output: +22 dbu maximum input levels mic input: +12 dbu, gain @ +10 db line input: +30 dbu, gain @ +10 db tape input and aux returns: +22 dbu input impedance mic input: 2120 vac, 60 hz; europe: 240 vac, 50 hz; japan: 100 vac, hz; korea: 220 vac, 60 hz dimensions: 12"w x 8"d (41x133x203mm) weight: 17 kg) no se atienden emergencias toda comunicacion es via ws o correo electronico condiciones de venta: - transferencia o deposito - entrega personal solo en maracaibo (previo acuerdo) - envios cargo y riesgo del comprador - ofertar solo si esta seguro de la compra en caso de no concretar en 3 dias se calificara negativo consultar disponibilidad antes de ofertarconsola tapco mix 50 como nueva muy poco uso features 1 mono mic/line input 2 stereo line inputs cd/tape input/output ultra-portable compact design fits almost anywhere rugged metal chassis takes all the punishment life can dish out intuitive layout gives access to all controls kensington security lock keeps mixer secure specifications mix
-
The t8's audio transformers have flat, wide frequency response and handle high signal levels while maintaining an isolated balanced outputthe t8 fits easily into virtually any audio system and is a clean patch point between all types of systems4db @ 100kohm load, 57kg) garantía: sin garantíaxlr, 1/4", and rca connections on all inputs and outputs offers connection versatility5db @ 600 ohm load input connections: xlr female balanced, o" trs balanced, and rca type phono jacks output connection: xlr male balanced, o" trs balanced, and rca type phono jacks power requirements: totally passive dimensions: 15db @ +4dbu thd: 001% typical @ 1khz, +18dbu, channel separation 90db typical cmrr: 60db typical phase error less than 5%, 20hz—20khz insertion loss: 0the t8 works great as an interface between a computer-based audio workstation and a monitor system, isolation on long cable runs in a fixed installation, isolation of multiple signal sources from recording equipment, or a safer connection between 2 audio systemsart t8 8-channel transformer isolator say goodbye to hum with the t8reversible mounting ears allow either the xlrs or the 1/4" and rca jacks on the frontcomes in a road-rugged 19", 1u all-steel black caseput this in your cart! specifications t8 8-channel transformer isolator frequency response: 10hz—50khz, +/-0this allows a clean, neutral sound with a wide variety of signal sourceshigh-quality passive audio interface uses 8 transformers to separate input and output signal grounds, isolating 2 systems and reducing hum and ground-loop noisethe transformers are wound for 1:1 unity gain and are designed for 600 ohm to 100kohm impedancefeatures high-quality passive audio interface 8 transformers to separate input and output signal grounds clean, neutral sound with a wide variety of signal sources xlr, 1/4", and rca connections on all inputs and outputs reversible mounting ears help yourself to low-noise, flexible connectivity5mm x mm x 95mm) weight: 3
-
The t8's audio transformers have flat, wide frequency response and handle high signal levels while maintaining an isolated balanced outputthe t8 fits easily into virtually any audio system and is a clean patch point between all types of systems4db @ 100kohm load, 5xlr, 1/4", and rca connections on all inputs and outputs offers connection versatility5db @ 600 ohm load input connections: xlr female balanced, o" trs balanced, and rca type phono jacks output connection: xlr male balanced, o" trs balanced, and rca type phono jacks power requirements: totally passive dimensions: 15db @ +4dbu thd: 001% typical @ 1khz, +18dbu, channel separation 90db typical cmrr: 60db typical phase error less than 5%, 20hz—20khz insertion loss: 0the t8 works great as an interface between a computer-based audio workstation and a monitor system, isolation on long cable runs in a fixed installation, isolation of multiple signal sources from recording equipment, or a safer connection between 2 audio systemsart t8 8-channel transformer isolator say goodbye to hum with the t8reversible mounting ears allow either the xlrs or the 1/4" and rca jacks on the frontcomes in a road-rugged 19", 1u all-steel black caseput this in your cart! specifications t8 8-channel transformer isolator frequency response: 10hz—50khz, +/-0this allows a clean, neutral sound with a wide variety of signal sourceshigh-quality passive audio interface uses 8 transformers to separate input and output signal grounds, isolating 2 systems and reducing hum and ground-loop noisethe transformers are wound for 1:1 unity gain and are designed for 600 ohm to 100kohm impedancefeatures high-quality passive audio interface 8 transformers to separate input and output signal grounds clean, neutral sound with a wide variety of signal sources xlr, 1/4", and rca connections on all inputs and outputs reversible mounting ears help yourself to low-noise, flexible connectivity5mm x mm x 95mm) weight: 3
-
The t8's audio transformers have flat, wide frequency response and handle high signal levels while maintaining an isolated balanced outputthe t8 fits easily into virtually any audio system and is a clean patch point between all types of systems4db @ 100kohm load, 5features high-quality passive audio interface 8 transformers to separate input and output signal grounds clean, neutral sound with a wide variety of signal sources xlr, 1/4", and rca connections on all inputs and outputs reversible mounting ears 19", 1u all-steel black casehelp yourself to low-noise, flexible connectivityxlr, 1/4", and rca connections on all inputs and outputs offers connection versatility5db @ 600 ohm load input connections: xlr female balanced, o" trs balanced, and rca type phono jacks output connection: xlr male balanced, o" trs balanced, and rca type phono jacks power requirements: totally passive dimensions: 1put this in your cart! specifications frequency response: 10hz”50khz, +/-05db @ +4dbu thd: 001% typical @ 1khz, +18dbu, channel separation 90db typical cmrr: 60db typical phase error less than 5%, 20hz”20khz insertion loss: 0overview say goodbye to hum with the t8the t8 works great as an interface between a computer-based audio workstation and a monitor system, isolation on long cable runs in a fixed installation, isolation of multiple signal sources from recording equipment, or a safer connection between 2 audio systemsreversible mounting ears allow either the xlrs or the 1/4" and rca jacks on the frontcomes in a road-rugged 19", 1u all-steel black casethis allows a clean, neutral sound with a wide variety of signal sourceshigh-quality passive audio interface uses 8 transformers to separate input and output signal grounds, isolating 2 systems and reducing hum and ground-loop noisethe transformers are wound for 1:1 unity gain and are designed for 600 ohm to 100kohm impedance5mm x mm x 95mm) weight: 3
-
The t8's audio transformers have flat, wide frequency response and handle high signal levels while maintaining an isolated balanced outputthe t8 fits easily into virtually any audio system and is a clean patch point between all types of systems4db @ 100kohm load, 5features high-quality passive audio interface 8 transformers to separate input and output signal grounds clean, neutral sound with a wide variety of signal sources xlr, 1/4", and rca connections on all inputs and outputs reversible mounting ears 19", 1u all-steel black casehelp yourself to low-noise, flexible connectivity6mm x 95mm) weight: 3xlr, 1/4", and rca connections on all inputs and outputs offers connection versatility5db @ 600 ohm load input connections: xlr female balanced, o" trs balanced, and rca type phono jacks output connection: xlr male balanced, o" trs balanced, and rca type phono jacks power requirements: totally passive dimensions: 1put this in your cart! specifications frequency response: 10hz”50khz, +/-05db @ +4dbu thd: 001% typical @ 1khz, +18dbu, channel separation 90db typical cmrr: 60db typical phase error less than 5%, 20hz”20khz insertion loss: 0overview say goodbye to hum with the t8the t8 works great as an interface between a computer-based audio workstation and a monitor system, isolation on long cable runs in a fixed installation, isolation of multiple signal sources from recording equipment, or a safer connection between 2 audio systemsreversible mounting ears allow either the xlrs or the 1/4" and rca jacks on the frontcomes in a road-rugged 19", 1u all-steel black casethis allows a clean, neutral sound with a wide variety of signal sourceshigh-quality passive audio interface uses 8 transformers to separate input and output signal grounds, isolating 2 systems and reducing hum and ground-loop noisethe transformers are wound for 1:1 unity gain and are designed for 600 ohm to 100kohm impedance
Caracas (Distrito Capital)
-
A 4-in, 4-out design, the mx400 series offer unprecedented connectivity through trs balanced i/o (mx400)lexicon mx400 dual stereo/surround reverb processor features: 4-in, 4-out dual stereo or surround effects processor usb computer connection vst/au plug-in allows software control of hardware unit lexicon-quality reverbs, delays, and effects built-in dbx dynamics processing includes 4-channel surround algorithms trs balanced i/o (see mx400 the mx400 delivers lexicon-caliber reverbs with the flexibility of a plug-in! garantía: garantia del fabricantelexicon mx400 dual stereo/surround reverb processor at a glance: wide array of reverbs, delays, effects, and dbx dynamics "hardware plug-in" gives you software control of the unit intuitive front-panel controls for live use wide array of reverbs, delays, effects, and dbx dynamics featuring a wide array of rich, complex reverb algorithms, delays, effects and dbx dynamics, the mx400 series is an ideal package equally suited for the home studio or live useintuitive front-panel controls for live use equally at home for live applications, the mx400 supplies the foh/live sound engineer intuitive front panel control with a backlit lcd screen for parameter displaysbring those quality sounds to project studios, surround facilities on a budget, and live sound applicationsin any application, the mx400 series products provide versatility and sound that is unmistakably lexiconintuitive front-panel controls for live use like its award nominated sibling, the mx200, the mx400 series has removed the compromises associated with using hardware in the home studio environmentel mas completo de los efectos lexicon el equivalente a tener 4 unidades de efectos procesadores en uno solo ademas de poderlo incertar como un pluging en tu daw rich lexicon reverbs with plug-in convenience! lexicon is noted for reverbs, and now the new mx400 and mx400xl dual stereo/surround reverb processorsthe new single-rackspace, 4-in, 4-out mx400 combines an intuitive front-panel design with lexicon's "hardware plug-in" technology, a unique usb connection, and vst/au interface for use with software recording platformsthe usb "hardware plug-in" format allows you to have complete plug-in control over your mx400 within any vst or audio units software environment, enabling you to control all automation and recall parameters exactly as you would with any software plug-in while enjoying the sonic benefits only hardware can providethe mx400 series also offers an affordable entry into the ever-expanding world of surround applicationsboth products also offer 4-channel surround algorithms, making them an extremely affordable offering to surround mixing facilities
-
Pregunte antes de ofertar características: 2? dual (per channel):w 4? dual (per channel): w 8? dual (per channel):w 4? (bridge / mono):w 8? (bridge / mono):w amplifier type:class h frequency response:15hz-25khz (+0/-1db) total harmonic distortion (thd): input impedance (balanced):10k ohm balanced to ground power supply:v 60hz or v 50hz dimensions:482 x 383 x 132mm (standard 19" rackmount width + 3u) net weight:77 lbs (38 kg)amplificador sound barrier pcs capacidad de mover 8 bajos rcf p 300 relajado comprobado, vendo por necesitar el dinero, cambio por amplificador mas grande serie capitan o similares
-
An integral crossover also provides balanced, line-level, stereo, highpassed outputs to feed powered satellite speakers or an external amplifier for passive satellites4 kg (89 lb) low frequency driver jbl -g input connectors xlr/m (x2) (line level, balanced)specifications ^ power rating 300 w / 500 w frequency range 38 hz - 300 hz (-10 db) dimensions (h x w x d) 597 mm x 516 mm x 597 mm (23transferencias banesco mercantil vzla bsbuilt-in 500 w (peak), 300 w (continuous) amplifierfeatures ¿ the rugged enclosure is constructed from 19 mm (25 in ts phone jack is provided25 in ts phone jack (x1) (speaker level) output connectors xlr/f (x2) (selectable, thru or high pass)the enclosure is covered in black carpetan led illuminates to indicate that limiting is taking placeintegral, preset limiter prevents clipping distortionline-level stereo inputs are summed before being sent to the subwoofer's internal amplifierthis input is useful in applications, such as those employing powered mixers, in which it is more practical to bring a full-range, speaker-level signal to the subwoofer amplifier75 in) mdf (medium density fiberboard) using advanced adhesives and mechanical fastener technology for durability and improved lowfrequency performancecontrols, connectors, and indicators are clearly labeled with large, highcontrast graphics for easy operation in poorly lit environmentsheavy duty, all steel handles are usedthis feature allows the jrx118sp to operate in stereo systems using a single subwooferpowered subwoofer for those who prefer the simplicity of a self-powered subwoofer, there's the jrx118sp5 in) frequency response 55 hz - 300 hz (±3 db) maximum spl 123 db weight 40a top mounted, cast aluminum 35 mm pole mount receptacle can receive an optional ss3bk pole to facilitate use of the jrx118sp as a base for a mid-high speaker cabineta speaker-level
-
5mm mini jack outputs: 5 unbalanced stereo/balanced mono, 1vpp/50 on 3it takes one stereo input and distributes the signal to five identical stereo outputs technical specifications input: 1 unbalanced stereo/balanced mono, 1vpp/33k on a 3the 105a is a high-performance distribution amplifier for unbalanced stereo audio signals96") w, d, h product weight: 03lbs) approx included accessories:power supply el precio indicado es por cada uno5db) coupling: ac audio thd + noise: nd harmonic) powerconsumption:12v dc, 100ma productdimension: cm x 75mm mini jacks maxoutput: 5vpp audio bandwidth (-3db):20khz s/n ratio: 80db unweighted control: left and right gain rear trimmers (0 to +3
-
W @ 4o bridged damping factor handles 2 ohm loads preguntar precio y existencia antes de ofertar xlr balanced & combi (xlr & 1/4" trs) balanced and unbalanced input connectors per channel class h circuitry for ultimate reliability & efficiency high current binding post (bridge mode) and speakon type outputs per channel mode selector switch (parallel, stereo, bridged) compressor on / off switch input sensitivity switch (17v) ground lift switch led indicators for signal, clip, level and protection for each channel parallel and bridge mode led indicators precision rotary level controls standard 19" rackmount width + 2u height dual variable speed cooling fans amplificador sound barrier pcs nuevo de paquete somos tienda física en san cristóbal tariba tenemos punto de venta
-
Ensure® original vanilla nutrition shake complete, balanced nutrition for everyday health each bottle of ensure original, from the #1 doctor-recommended brand* ensure, provides complete, balanced nutritionhacemos envios nacionales por tealcaaceptamos zelle bofa y cash no somos tienda fisicapor favor haga todas las preguntas necesarias antes de ofertarventa minima 6 litrosconfirme disponibilidad y precio al diaevery ready-to-drink shake has: 9 grams of high-quality protein 26 essential vitamins and minerals, including antioxidants† 25% of the daily value of b vitamins‡ to support brain health delicious vanilla flavor additional information: gluten-free suitable for lactose intolerance§ halal kosheraceptamos transferencias banesco y mercantil en bstrabajamos previo pago sin excepción en bs y usd
Baruta (Miranda)
-
Ensure® original milk chocolate nutrition shake complete, balanced nutrition for everyday health each bottle of ensure original, from the #1 doctor-recommended brand* ensure, provides complete, balanced nutritionhacemos envios nacionales por tealcaaceptamos zelle bofa y cash no somos tienda fisicapor favor haga todas las preguntas necesarias antes de ofertarventa minima 6 litrosconfirme disponibilidad y precio al diaevery ready-to-drink shake has: 9 grams of high-quality protein 26 essential vitamins and minerals, including antioxidants† 25% of the daily value of b vitamins‡ to support brain health delicious milk chocolate flavor additional information: gluten-free suitable for lactose intolerance§ halal kosheraceptamos transferencias banesco y mercantil en bstrabajamos previo pago sin excepción en bs y usd
Baruta (Miranda)
-
W @ 4o bridged damping factor handles 2 ohm loads xlr balanced & combi (xlr & 1/4" trs) balanced and unbalanced input connectors per channel class h circuitry for ultimate reliability & efficiency high current binding post (bridge mode) and speakon type outputs per channel mode selector switch (parallel, stereo, bridged) compressor on / off switch input sensitivity switch (1somos tienda en san cristóbal tariba7v) ground lift switch led indicators for signal, clip, level and protection for each channel parallel and bridge mode led indicators precision rotary level controls standard 19" rackmount width + 3u height dual variable speed cooling fansamplificador sound barrier pcs nuevo de paquete
-
2 clase 1 3 ajustes de sonido eq: jlab signature, balanced, bass boostpara avanzar reproducir pausar subir volumen bajar volumen2 clase 1 para un sonido claro y atrevido 3 ajustes de sonido eq: jlab signature, balanced, bass boost encendido automático y conexión fuera de la fundacontroladores bluetooth in 2 juegos de puntas de gel de silicona 2 juegos de aletas de empuje jlab micrófono en ambos auriculares para llamadas telefónicas***** condiciones para la venta ***** 1***** titulo completo ***** jlab audio jbuds air true wireless signature auriculares bluetooth + funda de carga resistencia al sudor ip55 conexión bluetooth 4resistencia al sudor ip55 conexión bluetooth 43 ajustes de ecualización, no requiere aplicacióncontroles de auriculares***** otras caracteristícas *****enviamos su compra a cualquier parte del paísposeemos tienda física donde puede retirar su compra (cuando se le indique que esta lista para ser retirada)tiempo de entrega de 5 días hábiles***** descripción del producto ***** horas de reproducción bluetooth 3 4 horas de duración de la batería bluetooth en cada auricular, 10 horas extra en el caso de carga incluido de 500 mah
-
2? dual (per channel):w 4? dual (per channel): w 8? dual (per channel):w 4? (bridge / mono):w 8? (bridge / mono):w amplifier type:class h frequency response:15hz-25khz (+0/-1db) total harmonic distortion (thd): input impedance (balanced):10k ohm balanced to ground power supply:v 60hz or v 50hz dimensions:482 x 383 x 132mm (standard 19"¿ rackmount width + 3u) net weight:77 lbs (35 kg) equipo totalmente nuevo de paquete somos tienda fisicasolo oferte si esta seguro de su comprar el precio es 800 verdes
-
2? dual (per channel):2800w 4? dual (per channel): 2100w 8? dual (per channel):1400w 4? (bridge / mono):5600w 8? (bridge / mono):3100w amplifier type:class h frequency response:15hz-25khz (+0/-1db) total harmonic distortion (thd): input impedance (balanced):10k ohm balanced to ground power supply:110-120v 60hz or 200-240v 50hz dimensions:482 x 383 x 132mm (standard 19"¿ rackmount width + 3u) net weight:77 lbs (35 kg) equipo totalmente nuevo de paquete somos tienda fisicasolo oferte si esta seguro de su comprar el precio es 800 verdes
San Cristóbal (Táchira)
-
Características: 200w rms (400w peak) per channel at 8 ohms 300w rms (600w peak) per channel at 4 ohms 600w rms (1200w peak) at 8 ohms bridged bi-polar output stage technology for the finest sound quality and reliability high output power to drive professional loudspeakers without clipping comprehensive protection circuitry with protect led indicator 1/4? trs & xlr balanced/unbalanced inputs speakontm & 1/4? speaker outputs three modes of operation ? stereo parallel mono, and mono bridge ground lift switch decibel (db) level meter with clip leds selectable voltage for worldwide operation dual aluminum extrusion heat sink design with directly mounted output transistors for no-fault operation air guide with front-to-rear airflow and cooling fan for thermal stability and reliability compact 2u well balanced enclosure steel reinforced chassis frequency response of 30hz ? 50 khz signal to noise ratio of 100 db below rated power at 8 ohms amp power ratings are measured using eia standardsgemini gpa4000 professional power amplifier en muy buenas condicionesgemini's gpa series power amplifiers provide you with excellent value for a wide range of intermediate power applicationswith its bi-polar output stage technology and comprehensive protection circuitry to prevent overheating, the gpa series gives you the high-end features you want in a product that is well within your budget
Mérida (Mérida)
$ 2
-
5 db input connectors balanced xlr, 1/4" trs, rca amplifier power lf/hf: 95 w / 70 w crossover frequency 2especificaciones: frequency range 37 hz - 20 khz max spl continous each / pair: > 104 db / > 110 db max spkl peak each / pair: > 117 db / > 123 db input sensitivity 92 db spl / 1m @ -10dbv balanced input drivers (lf / hf) 8" (203 mm) 238g 1" (25 mm) 231h lf trim + 2 db / -3 db hf trim + 20 khz 4th-order acoustic linkwitz-riley enclosure 18 mm (3/4 in) mdf finish metallic anthracite pain / dark matte black pvc dimensions (h x w x d) 397 mm x 254 mm x 335 mm (156 in x 10 in x 13minitor de estudio como nuevo, no se uso casi, es uno solo, sin detalles, no tiene caja7 kg (28 lb) se vende en 150, del norte2 in) net weight 12
Sucre-Sucre (Sucre)
-
Quiet audio signal transformer balanced inputs and outputs result in superior rejection of rfi and electromagnetic hummain features high quality inputs and outputs the fp33 features balanced xlr inputs and outputs, switchable between mic and line level signalin addition the fp33 features 3both 48v and 12v phantom power are available and two 9 volt batteries provide up to 8 hours of use4 headphone monitor modes headphone monitor switch allows monitoring of left, left + right (mono), right and stereo audio signalsthe fp33 can also use ac power from a shure ps20 or ps20e power supplyisolated two-way talk back isolated two-way talk-back using monitor in and modified slate mic/tape out jackmix bus output the mix bus output jack allows users to cascade multiple fp33 mixers for simultaneous use5mm headphone outputsadditional features dynamic range greater than 100db wide range input gain controls handle hot signal levels link switch gangs inputs 2 and 3 to control a stereo microphone switchable low-cut filters on each input bi-color led signal presence and peak indicator for each input dual-clutched master gain control for versatile output level adjustment bi-color led limiter and peak indicator for each output two linkable output peak limiters with adjustable thresholds and release times slate microphone and slate tone with selectable functions mixer/monitor in switch (locking and momentary) internal monitor defeat switch for split-feed headphone operation 1/4" and 3compact rugged design the compact rugged plated metal chassis is made to withstand extreme heat and cold for full operation under harsh conditions5mm headphone outputs regulated voltage rails provide exceptional headroom battery check switch and low battery warning led external power operating range of 12 to 30vdc rugged, plated metal chassis operates for 8 hours on two 9 v alkaline batteries product information item weight 4the inputs and outputs can be switched between mic and line level signalperfect for isolating either "mid" or "side" signal when using stereo microphonesthe vu meters feature timed or toggled backlighting and are multifunctional5mm monitor and tape connections as well as both 1/4" and 3the fp33 has panning and level controls on channels 1-3, and the headphone monitor dial provides monitoring of either left or right, dual mono, or stereo signalshure fp33 overview the shure fp33 3-channel stereo mixer is a field mixer rugged enough to handle the elements and flexible enough for professional working environmentsthere's also a built-in tone oscillator for calibration needs, and the monitor in and modified slate mic/tape out jacks can be used for 2-way isolated talk backbuilt-in tone oscillator the fp33 provides a 1khz test tone oscillator for calibration of tape machines, meters etcit is suitable for electronic news gathering (eng), field production (efp), film, television and recording for sound designno se hacen envíos al interior del paisconsulte precio actualizado no se hacen envios al interior del pais mixer shure fp33 portatil / cine-video como nuevo, muy poco usofunciona perfectamentethere are additional 35mm monitor input and tape output jacksthe meters feature timed or toggled backlighting and are multifunctionalthe fp33 features 3 xlr inputs and left/right xlr outputsthe fp33's mix bus output jack allows users to cascade multiple fp33 mixers for simultaneous use, and the professional analog vu meters have proven much more durable against the elements than led, lcd, or fluorescent metersprofessional vu meters professional analog vu meters are more durable against elements than led, lcd, or fluorescent meters1 pounds package dimensions 8 x 748 and 12 volt phantom power both 48 and 12 volt phantom power is supported allowing up to 8 hours of use on two 9 volt batteriessolo retiro en personaalso allows tandem use with the shure fp32a
-
Amplifier power lf: 130 watts @ low-frequency driver impedance, amplifier power hf:50 watts @ high-frequency driver impedance, input sensitivity:-55 dbu to -2 dbu for rated output (mic/lineswitch in mic position) +9 dbu to +26 dbu for rated output (mic/lineswitch in line position) enclosure material:aluminum baffle, gray co-polymer enclosureand protective bezel audio connectors: input xlr/f, balanced loopoutxlr/m, balanced crossover freq75" diameter titanium diaphragm*** pregunte disponibilidad antes de ofertar*** corneta amplificada jbl eon 15-p1 specificationsfreq*entrega personal previo acuerdocoverage (-6 db): 60° nominal rated maximum spl: 127 db, @ 1 m (35 in) net weight: 21 kg (47 lbs) lf driver: integral frame with mm) driver,neodymium magnet, 2" differential drivevoice coil*solo venta no hago cambios400vrdes *realiza todas las preguntas antes de ofertarcoverage (-6 db): 90° nominal vert175 watts rating per ul, detachable iec (male)power connectorac input:switchable vac (± hztransf: banesco, mercantil, venezuela, provincial3 ft) dimensions (h x w x d): 686 mm x 430 mm x 444 mm(27 in x 17 in x 17*unica disponibleresponse (±3 db):65 hz - 16 khz horzferro-fluid cooledrange (-10 db): 47 hz - 18 khz freqhf driver: jbl h-1 1" (throat diameter) compressiondriver with 1
-
Eight ¼" trs connectors provide balanced line outputs for monitoring and interfacing with other outboard gearanalog inputs are sourced from the eight combo jacks as either xlr mic or ¼" trs balanced line inputsit features every kind of connection you need¿including award-winning octane¿ preamp technology on all eight analog inputs, adat, s/pdif, word clock and midi*routing in stereo pairscom for update availabilityit features every kind of connection you need including award-winning octane preamp technology on all eight analog inputs, adat, s/pdif, word clock and midithe quality of your preamps is critical to how your music soundsin addition, you can assign the master level control to all four output pairs to uniformly attenuate up to a 7professional connectivity for the most demanding projects the profire features essential connectivity for any studio, delivering rock-solid stability and optimal sound qualityit is also pro tools m-powered compatibleplease visit m-audiothe profire delivers the same award-winning octane technology with its eight onboard mic preamps, giving you pristine audio fidelity right from the start of your signal pathembraced by reviewers and audio professionals alike, m-audio set a new standard with the 8-channel octane¿ preampin addition, the profire allows master or slave operation via internal clock, adat optical, s/pdif and word clockjetpll technology for critically acclaimed jitter elimination pro tools m-powered compatible compatible for pc and mac from the manufacturer building on a legacy of award-winning firewire audio interfaces, the m-audio profire brings next-generation performance to your pc or mac host-based recording systemit¿s assignable to any or all of the four analog output pairs, so you can choose which output pair will feed your main monitorsonboard dsp mixer and router customize your setup and record the way you want thanks to the power and flexibility of the profire onboard dsp mixer and routermi eshop strato_ vintage es lo mejorm-audio¿s mature, stable drivers deliver solid performance and ultra-low latencyuse the router to select from up to 52 audio streams and send them to any of the 26 hardware outputsthis facilitates use of the line, instrument and mic ins¿including the preamps¿with other digital gearthis powerful interface delivers 26 x 26 simultaneous i/o, complete with an onboard dsp mixer sourced from up to 52 audio streamsyou can also choose whether the master volume knob influences either or both of the two headphone outputs, or operates independently of thempro tools m-powered compatible the profire is an extremely powerful interface for pro tools m-poweredstandalone operation the profire doubles as a standalone 8-channel preamp, 8-channel a/d-d/a converter and digital format converterin addition to exceptional sound, each preamp has a generous 75db gain range, 48v phantom power, and a -20db padusuarios de menos de 200 positivas o usuarios nuevos, solo se entregara y probara en persona previo pago envio y entrega: por mrw o tealca una vez confirmado el pago, el producto sera enviado en un periodo de 2 dias habiles a mas tardarsimilarly, the first eight adat optical input channels feed the eight analog outputs to provide d/a functionalityflexible i/o, top-quality sound and low latency round out an incredible recording environment that is file-compatible with many other pro and project studios around the worldm-audio profire high-definition 26-in/26-out firewire audio interface with octane preamp technology product description building on a legacy of award-winning firewire audio interfaces, the m-audio profire brings next-generation performance to your pc or mac host-based recording systemthe two front-panel headphone jacks feature separate sources and independent level controls for additional cue mixing flexibilityyou can also disable the d/a conversion to allow the analog input channels to route to both the analog and adat optical outputs¿transforming the profire into a standalone 8-channel mic pre with eight discrete analog outputs plus 8-channel adat outputwhen the second optical port is not used for a/d conversion, the profire can also convert coaxial s/pdif to optical s/pdifyou can also create presets and instantly recall these setups at a later datein addition, analog channels 1 and 2 provide easily accessible ¼" ts instrument jacks on the front panelin addition, profire offers easy firewire connectivity, extremely low latency, dual headphone outputs, front-panel " instrument inputs and standalone operation* **compatible with pro tools m-powered 7complete with octane preamp technology and premium a/d-d/a converters, you won¿t find a better sounding or more flexible host-based audio interface96khz and 18 x 18 i/o maximum with pro tools m-poweredcritically acclaimed jetpll jitter elimination technology ensures pristine audio quality and reliable synchronization all the way up to high-definition 24-bit/192khz resolutionpro tools m-powered compatible* the adaptable onboard dsp mixer allows you to select from any of the 26 hardware inputs and 26 software returns as sources for any of its 18 input channels¿allowing you to create up to eight stereo mixesin standalone mode, the eight analog inputs route to the first eight adat optical output channelsin addition, profire offers easy firewire connectivity, extremely low latency, dual headphone outputs, front-panel ¼" instrument inputs and standalone operationdigital i/o is available via 2 x 2 s/pdif and 16 x 16 adat lightpipe4 with downloadable updateuser-assignable master volume control the profire interface delivers a new level of flexible control via the customizable master volume knobthe unit also features critically acclaimed jetpll technology to provide extremely stable synchronization and eliminate jitter that can degrade audio qualityen caso de envio el prodcuto solo sera enviado a la oficina de mrw o tealca mas cercana al domicilio o trabajo del comprador para que la pase buscado mis artículos a la venta visita mis otros artículos que tengo a la ventahigh-definition 192khz sound and solid performance the profire employs high-quality converters to deliver sampling rates up to 192khz for pristine, high-definition sound quality
-
Output: 5 vpp (> +4dbm)power source: 12 vdc, 100maspecifications: level (gain) controlsoptions: va-50p power supply with six 12vdc outletsinput: 1 audio stereo/balanced mono,1vpp/33kohm; on a 3rk-t1, rk-t3 rack adapterscompact size - part of the kramer tools™ family of compact, high quality and cost effective solutionssolo retiro en personaconsulte precio actualizado no se hacen envios al interior del paisit takes one stereo input and distributes the signal to five identical stereo outputsaudio bandwidht: (-3db); 20khzs/n ratio - 80db (unweighted)thd: nd harmonic)kramer tools distribuidor amplificador 105a stereo 5 canales the kramer 105a is a high performance distribution amplifier for unbalanced stereo audio signals5mm mini phone connectordimensions (w, d, houtputs: 5 audio stereo/balanced mono 1vpp/50ohm; on 35-mm mini phone connectorscontrol: left and right gain rear trimmers (0/+3s/n ratio: 80db unweightedaccessories: power supply, mounting bracket
-
Amplifier power lf: 130 watts @ low-frequency driver impedance, amplifier power hf:50 watts @ high-frequency driver impedance, input sensitivity:-55 dbu to -2 dbu for rated output (mic/lineswitch in mic position) +9 dbu to +26 dbu for rated output (mic/lineswitch in line position) enclosure material:aluminum baffle, gray co-polymer enclosureand protective bezel audio connectors: input xlr/f, balanced loopoutxlr/m, balanced crossover freq75" diameter titanium diaphragm*** pregunte disponibilidad antes de ofertar*** corneta amplificada jbl eon 15-p1 specificationsfreq*entrega personal previo acuerdocoverage (-6 db): 60° nominal rated maximum spl: 127 db, @ 1 m (3*solo venta no hago cambioshf driver: jbl 2418h-1 1" (throat diameter) compressiondriver with 15 in) net weight: 21 kg (47 lbs) lf driver: integral frame with 15" (380 mm) driver,neodymium magnet, 2" differential drivevoice coilac input:switchable 115 - 230 vac (±10%), 50 - 60 hzcoverage (-6 db): 90° nominal vert175 watts rating per ul, detachable iec (male)power connector400vrdes *realiza todas las preguntas antes de ofertartransf: banesco, mercantil, venezuela, provincial3 ft) dimensions (h x w x d): 686 mm x 430 mm x 444 mm(27 in x 17 in x 17*unica disponibleresponse (±3 db):65 hz - 16 khz horzferro-fluid cooledrange (-10 db): 47 hz - 18 khz freq
Girardot-Aragua (Aragua)
-
5 db input connectors balanced xlr, 1/4" trs, rca amplifier power lf/hf: 95 w / 70 w crossover frequency 2especificaciones: frequency range 37 hz - 20 khz max spl continous each / pair: > 104 db / > 110 db max spkl peak each / pair: > 117 db / > 123 db input sensitivity 92 db spl / 1m @ -10dbv balanced input drivers (lf / hf) mm) 238g 1" (25 mm) 231h lf trim + 2 db / -3 db hf trim + 20 khz 4th-order acoustic linkwitz-riley enclosure 18 mm (3/4 in) mdf finish metallic anthracite pain / dark matte black pvc dimensions (h x w x d) 397 mm x 254 mm x 335 mm (156 in x 10 in x 13minitor de estudio como nuevo, no se uso casi, es uno solo, sin detalles, no tiene caja7 kg (28 lb) se vende en 150, del norte2 in) net weight 12
-
The mixer offers 2 mono channels with balanced mic and line inputs, plus 2 stereo channels with 1/4" and rca line inputscompact and versatile design is ideal for home or project studio recording, computer audio, or live applications - 2 mono channels with balanced mic and line inputs, plus 2 stereo channels with 1/4" and rca line inputs - each channel has trim, 3-band eq, aux send, pan, and level controls with peak leds - standard 3the durable steel casing provides lasting durability and reliability perfecto estado en su caja con su adaptador de corriente original leer ==>> 100 verdes0 interface lets you connect to a computer to send and receive audio - combined, the mixer offers 15 simultaneous inputs and 10 outputs including the usb interface - ultra low-noise preamps provide excellent signal integrity, a full frequency response, and a wide dynamic range with superior headroom - globally selectable 48v phantom power is provided for use with condenser microphones - separate outputs are provided for main mix, control room, and headphones - stereo aux connectors, return inputs with level control, digital i/o, and rca tape/rec i/o connectors are all provided for additional connectivity - dual 4-segment led meters provide visual monitoring - the mixer employs smd technology in order to achieve a compact design5mm i/o connectors let you connect mp3 players, cd players, headphones, and morealtogether, the mixer offers 15 simultaneous inputs and 10 outputs including the usb interfacethere are also stereo aux connectors, return inputs with level control, and rca tape/rec i/o connectorsdual 4-segment led meters provide visual monitoring5mm i/o connectors let you connect mp3 players, cd players, headphones, and more - an integrated usb 1an integrated usb 1nady mm-15usb overview the mm-15usb from nady is a compact and versatile desktop mini mixer, ideal for home or project studio recording, computer audio, or live applicationsthe durable steel casing provides lasting durability and reliabilityeach channel has trim, 3-band eq, aux send, pan, and level controls with peak ledsthe mixer uses ultra low-noise preamps to provide excellent signal integrity, a full frequency response, and a wide dynamic range with superior headroomseparate outputs are provided for main mix, control room, and headphonesglobally selectable 48v phantom power is provided for use with condenser microphonesthe mixer employs smd technology in order to achieve a compact design0 interface lets you connect to a computer to send and receive audio
-
Contiene 3 drivers un driver dinamico de grafeno de 10 mm (dd) dual magnetic para frecuencias bajas un driver balanced armature (ba) para frecuencias altas y un driver balanced armatura para frecuencias media especificacion sonora: la descripcion del sonido es: bajos realzados de gran profundidad, agudos con gran nivel de detalle sin llegar a ser sibilantes, buen rendimiento de medios, con un soundstage relativamente amplio, como son pequeños tiene una gran comodidad y hasta se puede acostar a dormir con los audifonos puestos75mm tipo c -sensibilidad: 111 db -rango de frecuencias: 7hz - hz -longitud del cable: 12m sirven tanto para monitoreo y retorno como para disfrute de musica con calidadespecificaciones: -resistencia: de 24 ohm -cable: trenzado de 4 hilos con plug 3audifono kbear modelo kb d0l4rs kb 06: todos las frecuencias reproducidas por tres componentes con una fidelidad increíble, con una comodidad ergonomica muy alta, para todos los usos y todos los gustos acabado en resina endurecida y metalentregas personales en san diego el remanso, delivery en valencia (costo adicional) envios a nivel nacional aceptamos zelle bs d0l4rs somos serviclicks (issntgrm)5 bañado en oro -pin: doble 0
-
Their tube mp project series microphone preamplifier is also high-quality that allows you to connect guitars, keyboards and electronic drum kits to your mixerwhat's more, there are special grooves on the housing as well as the strips which makes it possible to stack units on top of each othersleek and sturdy design the technical components of this device are contained in a rugged aluminium housingclever thinking by art! crystal-clear sound your input signal is reproduced with amazing clarity, allowing you to make remarkably high-quality recordings with a maximum output of 70 db! the art tube mp project series microphone preamplifier is the perfect partner for professional audio work! características del producto compact microphone preamplifier tube type: selected 12ax7a tube suitable for mics and other instruments frequency range: (-100 db): 20 hz to 20 khz) frequency response: 10 hz to 40 khz input impedance: 300 ohms (xlr female balanced), 1 meg ohms (jack) output impedance: 600 ohms (xlr male balanced) 300 ohms (jack) gain: maximum 70 db (xlr - xlr), +50 db (jack - xlr) gain pad: switchable, 20 db maximum input volume: +17 dbu (xlr), +16 dbu (jack) maximum output volume: +20 dbu (xlr), +26 dbu (jack) xlr input impedance: switchable, 414 kg entrega jnmediatafotos reales zelle ref 90rubber strips on the underside ensure extra grip on your desk top or flight case7 ohms (xlr), 840 kohms (jack) low cut filter: switchable, -3 db at 40 hz output phase: switchable output limiter type: switchable phantom power: 48v switchable signal indicator: led robust aluminium housing dimensions: 150 x 165 x 44outgoing volume is indicated with bright ledsart has integrated user-friendly buttons and switches which are easy to operateart project series general art products deliver professional audio qualityprofessional microphone / instrument tube preamplifierviene en su caja incluye adaptador de corriente
-
Le faltan tres tapitas pero los potenciometros funcionan perfectamente specifications: rms power output: 100-watts lf driver: 1 x 15" custom ampeg speaker hf driver: piezo tweeter preamp: solid-state power amp: solid-state tone controls: 3-band eq mid tone control: style balanced line out: yes cd/mp3 input: yes headphone output: yes dimensions (w x h x d inches): 21 x 21 x 16 weight: 62 poundscualquier cosa de valor que se pueda llevr en maleta proponer un buen cambio y lo considerotodo cambio podria ser por instrumentos pequeños o equipos pequeños, o telefonos; ipods, etc
-
5a at 240v intake hole size: 4" bag size (diameter x depth): " x 24" powder-coated paint impeller: 10" balanced cast aluminum air suction capacity: 537 cfm maximum static pressure: 7aspiradora industrial marca grizzly, se uso muy poco muy buena aspiradora americana motor size: 1 hp, 120v/240v, single-phase, pre-wired to 120v amps: 7a at 120v, 32" filter: 30 microns made in an iso companyapproximate shipping weight: 52 lbsoptional bag upgrade to 3-micron filtration: h